Consoles are not like a PC build. You cannot just swap out things and replace them with something new or something that works.
Basically, opening up a PC and fixing it on your own is a lot easier than a console. However, you cannot even open up your console if you don’t want to void your warranty. It is advised that only a professional should tear the console and nobody else.
That is why troubleshooting steps are very limited. But very effective. Often a hard reset will fix everything up.
Why won’t my Nintendo Switch turn on?
It is heartbreaking when you cannot turn on your console, especially after a hard reset, because you were probably looking for a fresh start.
I have been using Nintendo since the Nintendo DS days, and I have some guidelines on these issues that you can easily by reading the guideline.
So keep reading till the end to get your desired fix.
It is very apparent that your Nintendo Switch power button is working, but your switch is not turning on because of some internal issue on hardware. It can be because there is not enough charge in your switch to boot up, or your switch is stuck on a black screen.
It is very common to dry out the whole battery life of the Nintendo Switch after a hard reset because the process is very lengthy, and it keeps the entire switch functional the whole time.
Most of the time, if your Switch won’t switch on, it’s because the battery is dead. Especially if it’s been a long time since it was charged, it may have lost even its remaining charge over time.
Wait at least an hour for it to recharge after you’ve plugged it back into its dock or using the charging wire that came with it. After a few more minutes of charging, the Switch will be ready to use.
So, let’s get started by getting the latest problem fixing Nintendo Switch Not Reading SD Card.
When the Nintendo Switch system is turned off or placed in sleep mode, it takes around 3 hours to completely charge the device. Charging time will be prolonged if the console is in use at the time of charging.
The battery life of the console, after completely charged, varies based on the model, as well as the software program and features that are being utilized on the console.
Now your switch might still not charge; if that happens, Check the AC adapter to see whether it’s operating correctly by plugging it in and out of the device and outlet. If it doesn’t work, wait a few more minutes and try again.
Even if the Switch is plugged into a charger, it might take several minutes for the battery to recharge to full capacity. Allow it to charge for a few hours before restarting. A low battery might take up to 24 hours to revive if you haven’t used your Nintendo Switch in days or weeks.
First and foremost, if your Switch isn’t charging, make sure the AC adapter is inserted into the power socket correctly. In addition, inspect the adapter for indications of wear and tear, such as cuts or tears. You’ll have to purchase a new adapter if your old one is damaged.
If you’re using the official USB-C power adapter that came with your Switch, you may reset the charger by unplugging it from the outlet and disconnecting it from the Nintendo Switch for around 30 seconds.
Now reconnect it to the outlet and the Switch and check to see whether it charges.
If it does not work, you may try either connecting the AC adapter into a different outlet or switching to an additional AC adapter.
It’s possible that an outlet is broken and won’t charge your device. A new outlet on a separate circuit could be a solution for you. Change rooms if you’re not sure where to look.
Remove your extension cable if you’re charging through it, and then try connecting into a wall outlet instead. Make certain that your electrical outlet works properly.
How to fix Nintendo Switch won’t turn on after hard reset
Even after a hard reset, if your Nintendo switch doesn’t turn on, it can be a little bit disappointing. Most of the time, it occurs when there is battery failure of some sort. Data corruption can be another reason behind it.
The charging wire is the most common culprit when the console won’t turn on. Make sure there aren’t any dents or scratches on it and that the charging cord is compatible with the dock.
You may not even be aware that your battery has run out. Switch users should be aware that if the battery is entirely depleted or not, the console’s screen will take a long to come on when it is placed into charging mode. Leave it to charge for an extended period of time after plugging the charging wire into the console properly.
It is not unusual to encounter this exact problem as a result of a software or firmware malfunction. A force restart should be performed as soon as possible if this situation occurs for you. If it doesn’t work, your only other choice is to do a hard reset.
But the problem can pretty much exist even after a hard reset. So follow the guideline written down below to land a solution.
Here are the steps to fix the Nintendo Switch won’t turn on after hard reset:
1. Charge your Nintendo Switch
I have discussed already that a hard reset would eat up almost 80% of your Switch battery, so it is very much possible that your Switch is out of battery, and that is why it won’t turn on.
This is the most typical explanation. After 30 minutes, try turning it back on and charging it in the dock.
If your Switch is charging properly, you’ll see a green light on the dock’s bottom left side. Make sure the dock is connected if the light does not come on. If that’s the case, but the light isn’t coming on, there may be a problem with your dock.
All you have to do is go through our latest Long Do Nintendo Switch Charge Last.
2. Try a different charging Dock
If your Switch doesn’t switch on, you may have a defective cable. Look for any dirt, exposed or frayed wires, a bent adaptor, or bent pins, and if you find them, do inspect them. Consider purchasing a replacement cable if there is any sign of wear and tear.
Keep in mind that using a non-Nintendo or the third-party power cord to charge your Switch might cause it to malfunction. Also, do not use any third-party Nintendo Switch dock because there is no guarantee that it won’t fry your charging port. If you are already using one, it is advised that you should ditch them as soon as possible and try to buy an official one.
You may have a faulty outlet or a surge protector even though your console and power connection are in perfect working order. The best way to figure out what’s wrong is to connect your Nintendo Switch to a different socket.
3. Perform another reset
If you are sure that your Battery is 100% fine and there is no damage to your charging port whatsoever, then you should perform another reset. It should work for you as it worked for many people in the past.
Here are the steps to reset Nintendo Switch:
- Locate the power button.
- Press and hold the power button for 20 secs.
- Release the power button.
- Wait for a few seconds.
- Turn on the switch.
You should be able to see the screen of the Nintendo Switch by this point. If you still don’t see the screen of the Nintendo Switch, follow the next method.
4. Remove the SD card
Your Nintendo Switch might not turn on because of potential data corruption. So if you have a MicroSD card, make sure to remove it before turning on the switch.
Here are the steps to remove the MicroSD card on the switch:
- Turn over the Nintendo Switch.
- Open the kickstand.
- Remove the MicroSD card.
- Press the power button.
If you don’t see the Nintendo logo, I am afraid there is something wrong with the hardware on your console, and it would be unwise to open it on your own and fix it. If you still have the warranty, I would suggest contacting Nintendo, either get a new Nintendo switch or a refund.
Have some time to spare? Quickly check out our epic guide on how to Fix a Water Damaged Nintendo Switch
Final Thoughts
Consoles are made to last at least an entire generation of gaming. But few unlucky ones see the black screen or blue screen of death even before hitting one year mark.
Hopefully, with this guideline, you can fix your issues. And you are welcome to reach out if you have any more queries.
